詳細描述日本進口油研單向節流閥

詳細描述日本進口油研單向節流閥

上海乾拓貿易有限公司 

　企業QQ：2880626087

　電話；021-69001039

　手機；17321017802（微信）

　郵箱；17321017802@163.com

　地址：上海市嘉定區江橋嘉涌路99弄6號樓713室

CRGM-03-50 CRGM-03X-50 CRGM-06-50 CRGM-06X-50 CRGM-10-50 CRGM-10X-50

污染控制必須注意保持對液壓油污染的控制，

否則可能導致液壓油的破壞，并縮短閥門的使用壽命。

which satisfy the recommended viscosity and oil temperatures given above. 

Control of Contamination Due caution must be paid to maintaining control over contamination of the hydraulic fluids 

Rc 3/8 Rc 1/2 Rc 3/4 Rc 1 Rc 1-1 / 4 Rc 1-1 / 2

Slacken the lock nut and turn the flow adjustment knob anti-clockwise to throttle flow. 

 After achieving satisfactory performance tighten the lock nut.

液壓油

TJ的粘度和溫度2粘度范圍在15 - 400 mm / s（77 - 1800 SSU）之間。

油溫在-15 / + 70°C（5 - 158°F）之間。

使用滿足上述給出的TJ粘度和油溫的液壓油。

which may otherwise lead t o breakdowns and shorten the life of the valves. 

 Please maintain the degree of contamination within NAS 1638-Grade 1 

松開鎖緊螺母，逆時針旋轉流量調節旋鈕以調節流量。

壓力平衡結構在高壓調節時提供較少的努力。

2.  Use 25 μm or finer line filter.

ONE WAY RESTRICTORS SRCT/SRCG-03/06/10 (3/8, 3/4, 1-1/4)

Fluid Types Any type of hydraulic fluid listed in the table below can be used 

約。質量kg（lbs。）

請保持NAS 1638-Grade 1內的污染程度

CRGM-03-5080 CRGM-03X-5080 CRGM-06-5080 CRGM-06X-5080 CRGM-10-5080 CRGM-10X-5080

3/8 BSP.F 1/2 BSP.F 3/4 BSP.F 1 BSP.F 1-1 / 4 BSP.F 1-1 / 2 BSP.F

CRGM-03-5090 CRGM-03X-5090 CRGM-06-5090 CRGM-06X-5090 CRGM-10-5090 CRGM-10X-5090

3/8 NPT 1/2 NPT 3/4 NPT 1 NPT 1-1 / 4 NPT 1-1 / 2 NPT

附件安裝螺栓

子板可用。從上表中子板型號。

當不使用子板時，安裝表面應具有良好的加工精加工。

 Pressure balanced construction provides less effort in adjustment at high pressure.

Recommended Viscosity and Temperatures 2  Viscosity ranging between 15 - 400 mm /s (77 - 1800 SSU).  

Oil temperatures between -15/+70°C (5 - 158°F).  Use hydraulic fluids 

2.使用25μm或更細的線路濾波器。

一路限制器SRCT / SRCG-03/06/10（3/8，3/4，1-1 / 4）

流體類型可以使用下表中列出的任何類型的液壓油

This valve is used to regulate an actuator speed in a circuit where line pressure is almost steady 

and small fluctuation of o il flow due to pressure changes is permitted.

達到滿意的性能后，擰緊鎖緊螺母。

Attachment Mounting Bolts

Sub-plates are available.  Specify the sub-plate model number from the table above.  

When sub-plates are not used, the mounting surface should have a good machined finish.

該閥用于調節線路壓力幾乎穩定的電路中的致動器速度，

并且允許由于壓力變化而導致的小流量波動。

集成止回閥允許從出口到入口的反向自由流動。

Integrated check valve allows reversed free flow from outlet to inlet port. 

詳細描述日本進口油研單向節流閥